ASTM A860 EBOOK

ASTM A Specification for fittings used in high pressure gas and oil transmission and distribution system. This standard is issued under the fixed designation A/AM; the number 1 This specification is under the jurisdiction of ASTM Committee A01 on Steel. ASTM A/AM Direct No.: + Fax No.: + Email: [email protected] Board No.: +

Author: Juzshura Kimi
Country: Nepal
Language: English (Spanish)
Genre: Life
Published (Last): 7 July 2012
Pages: 86
PDF File Size: 9.77 Mb
ePub File Size: 5.90 Mb
ISBN: 815-4-20982-633-8
Downloads: 45029
Price: Free* [*Free Regsitration Required]
Uploader: Taull

The nickel content of the deposited weld metal shall not exceed 1.

Referenced Documents astm a860 separately The documents listed below are referenced within the subject standard astm a860 are not provided as part of the standard. Combining values from the two systems may result in non-conformance with the standard. JIS G Steel pipes for low temperature service. And over, Sizes tested Section;min, specimen, thickness [7.

Rectangular For Less than [7. Wrought austenitic and austenitic-ferritic duplex stainless steels without specific inspection requirements BS EN Butt-welding pipe fittings Part 4: Link astm a860 Active A8660 link will always route to the current Active version of the standard.

Section V, Nondestructive Examination. A astm a860 analysis shall be performed on deposited weld metal for. In pallets, in plywood cases, in bulk. Within the text, the SI units are shown in asstm. JIS G Carbon steel pipes for pressure service. How can I help you? All butt — weld tees manufactured by cold —forming methods shall be liquid.

Research use only,Commercial use is prohibited.

All fittings shall be furnished in the heat-treated astm a860. After the removal of any cracksthe tees astm a860 be re- examined by the removal of any Acceptable tees shall be marked with the symbol PT or MTas applicableto indicate compliance.

Combining values from zstm two systems may result in nonconformance with this specification. This specification covers wrought high-strength low-alloy butt-welding steel fittings of seamless and electric fusion-welded construction for applications in high-pressure gas and oil transmission and distribution systems. No cracks shall be permitted.

Astm a860 personal shall be. Materials and Manufacture … Research use only,Commercial use is prohibited. A chemical analysis shall be performed on deposited weld metal for each heat of filler metal orfor submerged arc welding astm a860, each heat of filler metal and batch of flux the astm a860 metal shall be deposited in accordance with the qualified weld procedure.

astm a860

ASTM A860 Grade WPHY 65 Buttweld Pipe Fittings

Within the text, the SI units are shown in brackets. Astm a860 can I do for you? JIS Astm a860 Carbon steel pipes for high pressure service. Materials shall be heat treated by normalizing, quenching, and tempering or stress relieving. These fittings are w860 use in high-pressure gas and oil transmission and distribution systems.

JIS G Arc welded carbon steel pipes. Astm a860 G Carbon steel pipes for high temperature service. JIS G Stainless steel pipes. And over, Sizes tested Section;min. Astm a860 G Carbon steel pipes for ordinary piping. All values are Maximum unless A range is stated. By Sea or By Land Packing: Butt-welding fittings differing from these.

It is informational only and not an astm a860 part of the standard; the full text of the standard itself must be referred to for its use and axtm.

The chemical astm a860 thus determined shall conform to Table 1. If you want to use it ,you can buy from following link: Work Item s – proposed revisions of this standard.

Historical Version s – astm a860 previous versions of standard. Internal and external surface shall be examined when size permits permits accessibility.

The values stated in each system may not be exact astm a860 therefore, each astm a860 shall be used independently of the other.

These fittings are for use in high-pressure gas and oil transmission and distribution systems.

The material for fittings shall be fully killed fine — grain material made by a. The values stated in each system are not exact equivalents; therefore, astm a860 system must be used independently of the other. After the astm a860 of any cracksthe tees shall be re. Standard Specimen, Size Specimen. DIN Medium-weight threaded steel tubes. The product analysis shall be the basis for rejection. One or more of the astm a860 requirements may be specified in the order.